boilermate-repairs.co.uk

 

Home
 

Copyright 2007 to 2015 Michael Bryant

Protected by Copyscape Online Plagiarism Test

 

BoilerMate
BoilerMate II
Boilermate III
BoilerMate 2000
BoilerMate A-Class
 
BoilerMate A-Class Solar
 
BoilerMate A-class Ecodan Mitsubishi Heat Pump
 
 
Gledhill website
 
New!
"Faults & Fixes"
discussion forum
 
Replacing a Boilermate
 
 
Contact me
 
 
 

Sister sites:
Gledhill Repairs
PulsaCoil Repairs
BoilerMate Repairs
ElectraMate Repairs
SysteMate Repairs
Gulfstream Repairs

 
 
 
 
 

 

What IS a BoilerMate A-Class?

(Firstly, most Boilermates are qualified with II, III or 2000 or similar suffixes. The first, original BoilerMate was just called a BoilerMate without suffix. This page deals with the BoilerMate A-Class)

 

How does the BoilerMate A-Class work?

A conventional central heating boiler heats the water in the BoilerMate directly. The stored water is pumped to the boiler for heating and back again by one of of the three pumps behind the front panel of the unit whenever the stored water temperature drops below a specific temperature set in the factory. A second pump pumps this pre-heated water around the radiator circuits when central heating is required. 

The BoilerMate A-Class delivers hot water to the hot taps in a similar way to the previous BoilerMate III ands 2000 models, but without the user-adjustable thermostatic blender valve. A third pump starts when a hot tap is turned on and pumps hot store water through the plate heat exchanger, thus heating the cold mains water very effectively on it's way to the hot taps or showers.

The operation of the appliance is controlled by an unnecessarily complicated and poorly (in my opinion!) printed circuit board which also records certain functional errors and returns then when interrogated.

  

Common faults with the BoilerMate A-Class:

Surprisingly there are very few. Most of the problems with the Boielrmate 2000 and preceding models have been ironed out. I get very few calls for the Boilermate A-Class which probably explains why it took me so long to write this page :) These are about the only faults I see on an A-Class. Most other apparent faults turn out to be failure of the gas boilers heating them. Incidentally the Boilermate A-Class is often installed with Gledhill's first conventional gas-fired boiler, the GB10, GB20 or GB30. As usual, these are designed in a manner most heating technicians find perplexing but they are straightforward (usually) to fix. I'll write and publish a website for the Gledhill GB10-30 gas boiler soon!


1) Water scale-contamination of the plate heat exchanger.

The plate heat exchanger was hailed by manufacturers as the answer to water scaling, but this has proved not to be the case. Hard water in certain areas still seems capable of blocking a plate heat exchanger with calcium deposits causing restricted hot water flow from the taps and warm (instead of hot) temperatures. When the problem becomes acute the water flow slows to a trickle and the temperature swings wildly from scalding hot to stone cold. The answer is to fit a replacement plate heat exchanger, which takes around an hour (instead of several hours to de-scale the copper coil heat exchanger in early versions of the BoilerMate).. 

2) Circuit board failure. 

The board can be interrogated for faults by pressing the buttons on it in accordance with the manual. Unfortunately although the error codes are quite easy to find on the display, the manual doesn't mention what they mean! Any parameter reporting code "29" is an "internal communications error" on the control board, for which the fix is a new control board. 

 

 

If you'd like me to come and fix your BoilerMate A-Class, contact me now

 

Page first created 9th April 2014
Last updated 9th April 2014

Protected by Copyscape Web Plagiarism Scanner